The new generation of optical digital relay tester. 8 optical port design, and powerful data processing capability can realize full functional test of the optical digital protection devices. Equipped with GPS, IRIG – B code synchronization interface and supports the IEEE1588 to provide the conditions to substation internal debugging and substation to substation combine debugging. It integrated the unique functional include: the abnormal SV simulation, virtual terminal test, the optical power testing and so on. Efficient, fast to complete the intelligent station test.

Ponov Pro1

Features

  • 8 fiber optical ports for:
  • Receiving and sending IEC61850-9-2 format SV and GOOSE message
  • Receiving and sending IEE1588 message
  • Measuring received fiber optical power
  • Provide flexibility to configure both SV (IEC6185092) and  GOOSE ports independently.
  • Local control with quick control buttons
  • Each port can be configured as Receive and Send at the same time or it can be configured as Receive or Send.
  • Can check the GOOSE communication link
  • SV, GOOSE configure message can be saved and recall repeatedly
  • With the IEEE1588 synchronization function, deviation of the time is less than ±80ns
  • With GPS, IRIG-B code synchronization interface

1.3 Device Features

  • 8 fiber optical ports for:
    • Receiving and sending IEC671850-9-2 format SV and GOOSE message
    • Receiving and sending IEE1588 message
    • Measuring received fiber optical power
  • Provide flexibility to configure both SV (IEC61850-9-2) and GOOSE ports independently. Each port can be configured as Receive and Send at the same time or it can be configured as Receive or Send.
  • Strong data receiving and sending capability for each fiber optical port:
    • Can send 6 groups of SV at the same time
    • Can send 12 groups of GOOSE at the same time
    • Can receive 5 groups of GOOSE message
    • Can send/receive IEE1588 message
  • While sending SV, the dispersion of the MU is better than ±80ns
  • Can receive SV, realizing self-loop test
  • Fiber-optic communication ports from NO.1~NO.4 can be used to measure received optical power
  • 8 independent meeting IEC60044-7/8(FT3) format SV output port
  • Can simulate collector and output meeting IEC60044-8 format message to MU
  • 12 configurable independent low-level analog signal output terminals, can  be used to test the low-level signal input protection device
  • Can publish/subscribe many different GOOSE control block message
  • Analyze protection model file SCD、ICD、CID、NPI)automatically
    • Can configure SV, sample channel message, GOOSE message automatically
  • Can check the GOOSE communication link
  • SV, GOOSE configure message can be saved and recall repeatedly
  • Simulate the abnormal massage (jitter, frame loss, flying spot, wrong sequence, data anomalies, packet retransmission, channel invalid, out of step, etc.)
  • Software can communicate with the protection device directly
    • Read protection value, SV report and the other message by MMS
  • With the IEEE1588 synchronization function, deviation of the time is less than ±80ns
  • With GPS, IRIG-B code synchronization interface


2. Technical Parameters

2.1 Power Supply

Ponov Pro2

2.2 Ethernet Communication Interface

Ponov Pro3
 

Ponov Pro4

Ponov Pro 5

2.3 Low-level Signal Analog Output

Ponov Pro6

2.4 Binary

Ponov Pro7

Ponov Pro8

2.5 Synchronous Interface

Instrument provides three ways of synchronous interface:

  • IEEE 1588 synchronization: any fiber-optic communications interface can be used as a IEEE 1588
  • GPS synchronous interface: Optional PGPS02 (satellite synchronization equipment)
  • Light B code interface: interface type ST, connect fiber 62.5/125μm (multimode fiber) ST-ST

www.relaytest.com